Bay windows include character and area to a home 87937

Bay Windows Include Character And Space To A Home

It was the perfect area. Our California cattle ranch design house had a big picture window in the front room. The window extended from a few inches above the flooring to just a few inches below the cathedral ceiling. The walls and ceiling were redwood stained knotty pine and the flooring was a matching wood. The window kept an eye out over a flower bed, shrubs and the stretch of front yard. It was the best window to be replaced with a bay window.

The window was almost square. It was 72 X 72 inches. We considered a bow window, however chosen to install a bay window instead. We just felt that our particular house looked better with three panel bay window instead of the several panel bow windows. Our intent was to fill the seat board of the bay with potted plants we had sitting in front of the existing photo window. The new plan would give us a little more space in the space and enhance the total look of your house. It was time to go shopping.

Scratch vs. Pre-built

When we initially understood of installing the brand-new window, I began collecting prepare for constructing a bay window. Thumbing through books and magazines, and the Web online search engine, I found several prepare for developing a bay window from scratch. I also found that carrying out such a job was going to be unneeded. Most of the significant window makers, such as Pella, Milgard and Anderson make both entirely pre-assembled bay windows as well as pre-built parts for bay windows.

These days very couple of contractors will handle the project of developing a bay or bow window from scratch. It simply isn't useful when for the very same or less money they can install a high quality pre-built window. If the contractors use pre-built windows or parts for brand-new house building or renovation tasks, then we might do the same for our redesigning project, we reasoned.

Installing a bay window can quickly be a do-it-yourselfer project. Before you go the diy route, nevertheless, you might wish to line up a professional to help out if essential. This is not going to be a job that you can finish throughout a Saturday afternoon. Opportunities are you are not going to finish it in a weekend, for that matter.

You are also going to wish to line up some help. Bay windows and window parts are heavy. A minimum of they are too heavy for a single person to manage.

Be sure and have a look at the weather report, consisting of the long range projection. Setting up the window indicates opening a hole into your home. It can take a couple of days to get the brand-new window in place and sealed. The last thing you want is for rain to come gathering on your floor, walls or furnishings.

Be sure and check your city or community building and construction codes. There might be special regional requirements, such as having shatterproof glass in low profile windows. You are most likely going to need a structure license anyhow, so that is likewise a good time to check the codes.

Tools and Materials Needed

The tools you will need for this job consist of a tape measure, a framing square that you can likewise utilize as a straight edge, a circular saw or miter saw, crow bars, drill and bits, level, stapler, energy knife, tin snips and a caulking gun.

The materials you will require include the bay window system, the assistance brackets, nails, roof paper, shingles, roof nails, outside grade silicone caulking and fiberglass insulation. You will likewise require 1X6 inch boards for the window skirting. If you are enlarging an existing window, or if you are setting up the window in an area that was previously the wall, you will likewise require 2X4s for cripple studs and extra framing.

Basic Setup Steps

1. Establish window position in the wall. Eliminate the existing window. Measuring the bay window, mark on the exterior of your home the opening needed for the new window. Using your circular saw, cut the required opening.

2. Framing. Develop the framing for the new window. This will likely include cutting through existing studs and putting in a brand-new header, rough sill, jack studs and paralyze studs.

3. Set up the support braces. A window as much as 5 feet wide will take a minimum of two support braces. A wider window will need 3.

4. Set the window in place. Raise the bay window on the support braces and move it into the rough opening. Shim as required to level the window. Anchor in place.

5. Construct the window roofing. Set the roof frame on top of the bay window system and nail in place. Fill the space between the roof and the top of the bay window with insulation. Fasten the roofing system sheeting to the frame and cover with roofing paper. Set up the drip edges and the flashing and after that shingle.

6. Set up the window skirting around the bottom of the window. Fill will insulation and after that connect the skirt bottom to seal the beneath side of the window.

7. Seal the edges with silicone caulking.

This is a list of the standard installation steps and they have actually been abbreviated in the interests of simpleness and space. The window system you purchase will have total installation steps. Take it from the voice of experience; it actually makes the job go much more efficiently and it will be completed in much less time when you read and follow them.

In our case, I had two friends aiding with the project. We have collaborated on other projects and collaborate well. We had the old window out and the rough framing completed on Saturday afternoon. We buttoned up the hole with plywood over night and went back to work the next day. By Sunday night we had the new window installed and the roofing and skirting finished. On Monday afternoon I ended up sealing up the outside and completed the trim work for the inside.

And, we were right. It was the perfect area for a bay window. It looked fantastic from the exterior. Inside, it ended up being the centerpiece of the space and included a special charm to your house. The window offered your house included character and local plumber Dandenong value.

When it came time to sell the house, it was one of the features that were particularly appealing to the purchasers.