Setting up a new shower unit 15365

Setting Up a New Shower Unit

A successful shower setup requires cautious preparation and a lot of work. For the most part, you will require to do 3 kinds of jobs: framing walls, installing the pipes, and completing walls.

Preparation

Firstly, you should decide on the kind of shower that you wish to install. It is essential to ascertain whether the picked shower can handling specific systems and can control a safe level of water through the boiler. Many shower systems nowadays are designed to be versatile to various water pressures (such as saved hot water and cold mains).

It is also important to consider the water pressure and the planning of the piping and drain for the shower

Different Kinds of Shower Units

Push-on Mixer: The tube and spray parts of the push-on mixer shower system can be linked to the bath tap as per your requirement, and the water temperature level can be adjusted by means of the taps. Push-on mixers are low-cost and exceptionally simple to set up. However, although the pipe connection is simple, it is quickly dislodged. Furthermore, it is troublesome to adjust the temperature.

Bath/ Shower Mixer: The hose and spray of this type of shower are integrated with a bath mixer tap, and the temperature level can be adjusted through the bath taps. It is an extremely low-cost option and no additional plumbing is involved. Nevertheless, the bath/shower mixers likewise suffer from bothersome temperature control options.

Manual Mixer: The tube and spray of a manual mixer shower unit belong of the wall system and the hot and cold water supplies are linked to a single valve The temperature level and pressure of the water are managed through either one or a variety of knobs (in more pricey showers). Although temperature level control is a lot easier in manual mixer types, they are more costly than the formerly mentioned mixers. They also require additional pipes of cold and hot water supply pipes.

Thermostatic Mixer: The hose pipe and spray of this shower type are a part of the wall unit and the hot and cold water materials are connected to a single valve here too. It is Mornington plumbing company total with an integrated stabiliser to self-adjust the water temperature level and to prevent it from becoming too hot. One of the most significant advantages of a thermostatic mixer shower type consists of convenient temperature control. Nevertheless, it is the most costly of the various mixer choices.

Power Shower: A power shower is a single unit consisting of a powerful electric pump that is capable of modifying both the water pressure and temperature level. This type of shower can be fitted if there is water supply from a cold water cistern and a hot water cylinder. A power shower makes the adjustment of both pressure and temperature level easy. On the other hand, it disagrees for water heated up directly by the shower or where the water is supplied by a mix boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and it heats the water electrically. It is important to keep in mind that for this shower type to be installed, the mains pressure needs to be at least 0.7 kg/sq cm (10lb/sq in). The system permits the temperature level and pressure to be changed via a knob. Models with temperature level stabilisers are better as they stay untouched by other taps in other places in use within the household. A significant downside of electric showers is that the control knob only allows for the choice of heats at less pressure, or lower temperature levels at a greater pressure. This is troublesome in the winter season when the spray is typically weak and the mains water is chillier. Nevertheless, this problem is dealt with in some designs which are available with a winter/summer setting.

Method

Depending on the kind of shower you want to install, the shower head should either be fitted in order to prevent its contact with the water in the bath below or the base tray, or it should have a check valve.

Before beginning, it is suggested to mark the positions of the shower head and control, and to prepare the pipe-work involved. In addition, the drain system to get rid of the drainage will need to be planned. Both positions of the cable television route and the shower switch will likewise need to be considered if an instant or electric shower unit is being installed.

Use the instruction guide provided with the shower unit to fit the shower control.

Before fitting the pipes that will supply the water to the shower system, it is important to cut off the water system. In order to secure the pipelines, they must be given a waterproof covering and likewise fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the total look.

Fit the base tray, shower head, and fittings.

Connect the main shower control to the pipelines that will be providing the water (This might require a female screw thread adapter).

Reconnect the supply of water and test the pipes for any leaks, as some might require tightening.

If you are installing an electrical shower, remember to turn off the electrical power supply before making any electrical connections. Once these connections have actually been made (there must be assistance within the user's manual), the power supply can be changed back on.

Adjusting Water Pressure to Fit Your Shower

The cold water tank can be raised to a higher height (in some cases just 150mm (6inches)) by fitting a strong wood assistance underneath it-- possibly composed of struts and blockboards. If you choose this option, the primary and circulation pipelines will also have to be raised to fulfill the brand-new Baxter local plumbing height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is chosen, it needs to be linked into the power supply in order to operate.

Piping and Drainage

It is best to utilize 15mm size supply pipelines, and make the runs to the shower as short and straight as possible so regarding keep optimal pressure and reduce heat loss. In addition, by minimising making use of elbows for pipeline corners, you can reduce the resistance in the flow of the water supply. You can attain this by flexing the pipelines instead.

Most Common Mistakes

# Breaking or neglecting regional code restrictions.

# Using pipes that are too small.

# Connecting copper to galvanized without using a brass or dielectric fitting in between the two.

# Not utilizing tape or pipe substance at threaded joints.

# Not leveling your components when setting up them.

# Not installing an air space filling for fixtures.

# Cutting supply stub outs too brief to install the shutoff valves onto after the finished wall remains in place.

# Not correctly lining up tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leakage.)

# When turning the water back on in your home, constantly run the outside hose pipe valve or flush your toilets to bleed dirt and air from the lines. This particles can cause problems in your sink faucets and other plumbing trim.