Setting up a new shower unit 67310

Installing a New Shower Unit

A successful shower setup needs careful planning and a lot of work. Most of the times, you will require to do 3 types of jobs: framing walls, setting up the plumbing, and finishing walls.

Preparation

Firstly, you must decide on the type of shower that you want to set up. It is necessary to ascertain whether the selected shower is capable of dealing with particular systems and can manage a safe level of water through the boiler. Most shower systems nowadays are designed to be versatile to various water pressures (such as kept warm water and cold mains).

It is also crucial to consider the water pressure and the planning of the piping and drainage for the shower

Different Kinds of Shower Units

Push-on Mixer: The hose and spray parts of the push-on mixer shower system can be connected to the bath tap according to your requirement, and the water temperature level can be changed through the taps. Push-on mixers are inexpensive and very basic to install. Nevertheless, although the hose connection is basic, it is easily removed. In addition, it is troublesome to adjust the temperature level.

Bath/ Shower Mixer: The pipe and spray of this kind of shower are combined with a bath mixer tap, and the temperature can be changed through the bath taps. It is a very cheap alternative and no additional pipes is included. However, the bath/shower mixers also suffer from inconvenient temperature control alternatives.

Manual Mixer: The pipe and spray of a manual mixer shower unit belong of the wall system and the hot and cold water products are linked to a single valve The temperature level and pressure of the water are managed through either reliable plumber in Cranbourne one or a variety of knobs (in more expensive showers). Although temperature control is much easier in manual mixer types, they are more expensive than the previously pointed out mixers. They likewise require additional plumbing of cold and hot supply of water pipes.

Thermostatic Mixer: The hose pipe and spray of this shower type are a part of the wall system and the hot and cold water products are connected to a single valve here too. It is total with a built-in stabiliser to self-adjust the water temperature level and to avoid it from ending up being too hot. Among the greatest benefits of a thermostatic mixer shower type consists of convenient temperature level control. Nevertheless, it is the most pricey of the different mixer choices.

Power Shower: A power shower is a single system including a powerful electric pump that is capable of altering both the water pressure and temperature. This type of shower can be fitted if there is supply of water from a cold water tank and a hot water cylinder. A power shower makes the change of both pressure and temperature simple. On the other hand, it disagrees for water heated directly by the shower or where the water is provided by a mix boiler under mains pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and it warms the water electrically. It is essential to note that for this shower type to be set up, the mains pressure needs to be at least 0.7 kg/sq cm (10lb/sq in). The system permits the temperature and pressure to be adjusted through a knob. Designs with temperature stabilisers are much better as they stay untouched by other taps somewhere else in usage within the household. A significant drawback of electric showers is that the control knob just enables the option of heats at less pressure, or lower temperatures at a greater pressure. This is troublesome in the winter when the spray is frequently weak and the mains water is colder. However, this issue is dealt with in some designs which are offered with a winter/summer setting.

Method

Depending on the type of shower you wish to set up, the shower head need to either be suited order to avoid its contact with the water in the bath below or the base tray, or it must have a check valve.

Before beginning, it is a good idea to mark the positions of the shower head and control, and to plan the pipe-work included. Additionally, the drain system to eliminate the drainage will need to be planned. Both positions of the cable television path and the shower switch will likewise require to be thought about if a rapid or electrical shower unit is being installed.

Use the guideline guide offered with the shower system to fit the shower control.

Before fitting the pipes that will provide the water to the shower system, it is very important to cut off the water system. In order to safeguard the pipes, they ought to be offered a waterproof covering and also fitted with separating valves. The pipes can then be buried into the wall and plastered over to neaten the general look.

Fit the base tray, shower head, and fittings.

Connect the primary shower control to the pipelines that will be supplying the water (This might need a female screw thread adapter).

Reconnect the supply of water and test the pipelines for any leakages, as some might need tightening.

If you are setting up an electrical shower, keep in mind to switch off the electrical power supply before making any electrical connections. Once these connections have been made (there should be assistance within the instruction manual), the power supply can be changed back on.

Adjusting Water Pressure to Suit Your Shower

The cold water reservoir can be raised to a greater height (sometimes as low as 150mm (6inches)) by fitting a strong wood support below it-- perhaps composed of struts and blockboards. If you pick this alternative, the primary and circulation pipes will also have to be raised to satisfy the new height of the reservoir.

Alternatively, a booster pump (a single pump or a dual/twin pump) can be fitted. Whichever type is picked, it should be linked into the power supply in order to operate.

Piping and Drainage

It is best to use 15mm size supply pipes, and make the go to the shower as short and straight as possible so regarding keep optimal pressure and minimise heat loss. In addition, by minimising making use of elbows for pipe corners, you can reduce the resistance in the flow of the water system. You can attain this by flexing the pipelines instead.

Most Common Mistakes

# Breaching or neglecting regional code restrictions.

# Utilizing pipes that are too small.

# Attaching copper to galvanized without using a brass or dielectric fitting in between the two.

# Not using tape or pipe substance at threaded joints.

# Not leveling your fixtures when setting up them.

# Not setting up an air space filling for fixtures.

# Cutting supply stub outs too brief to install the shutoff valves onto after the ended up wall remains in place.

# Not effectively lining up tubing into fittings or stop valves. (Forcing the nut onto the compression ring at an angle when the tubing is at an angle will cause a leak.)

# When turning the water back on in your home, constantly run the outside hose pipe valve or flush your toilets to bleed dirt and air from the lines. This debris can cause problems in your sink faucets and other pipes trim.